Plain bearings help boost efficiency of solar energy plant

Igus plain bearings, rod end bearings and linear units are being used by Conergy to help maximise the efficiency of its solar energy systems

The SolarOptimus tracking mechanisms on the latest Conergy photovoltaic systems guarantee that the PV panels will always be at the right angle relative to the sun. The twin-axis drive systems are controlled by an astronomical algorithm that increases the production efficiency of eco-friendly energy by around 30 per cent. To enable the systems to run maintenance-free over longer periods even under extreme weather conditions, Conergy decided to use Igus components for all plain bearing applications, as well as rod end bearings and linear units.

The renewable energy market is growing at high rate. Conergy was founded in 1996 as a solar system integrator, and has been listed on the stock exchange since March 2005. Conergy has been able to increase its turnover since 2001 by a remarkable 1830 per cent, which makes Conergy one of the fastest growing technology companies in Europe.

Conergy provides complete systems for the production of renewable energy (wind, sun and biomass) all over the world - including project management, service and financing. In addition, the impressive growth rate is generated by the company increasingly developing and manufacturing its own products. For example, Conergy is currently investing around £200million in building the most modern production facility in Europe for fully integrated solar wafer, cell and module production in Frankfurt. When completed, this facility will employ around 1000 people.

Make of buy?

The question 'make or buy?' is always analysed very carefully. Bernd Krabbe, head of the Engineering and Service department in the Global Technology Team (GTT) Electronics at the company's design headquarters, comments: "We look around on the market and evaluate whether or not there is a system already available that meets our high customer requirements. If this is not the case, we develop a product of our own." In the case of tracking systems for photovoltaic systems, the existing products apparently did not live up to the demanding requirements, because Conergy recently presented its new system, known as the SolarOptimus.

This system has the task of optimising the alignment of the photovoltaic generators, which pays off for the plant operator, because energy production can be increased more than 30 per cent by utilising twin-axis tracking systems. In Northern Europe, this optimum position detection always moves to the brightest spot in cloudy conditions. In Southern Europe, on the other hand, where the sky is often cloudless and there is a high brightness level, a system that keeps the photovoltaic modules at a right angle to sunray incidence on the basis of astronomical data is more effective.

This control principle is also used by the SolarOptimus, which was developed for the radiation-intensive southern Europe regions. Product manager Philipp Vanicek says: "The modules are moved in two horizontal axes according to an astronomical algorithm." During development of the frame system, the main focus was on durability and freedom of maintenance, since the systems are often set up in remote areas without any on-site personnel. For this reason, the developers consciously eliminated complex drive systems, preferring to use components that have a straightforward but high-quality design. This applies to both the motors and the bearings. Bernd Krabbe, who is also project manager for the SolarOptimus development, states: "We explained our requirements to several suppliers of bearing systems and asked for their solution suggestions." It had to be considered that the set-up locations for the solar systems are often very dry, with high levels of sand and fine dust. Another factor is the very wide temperature spectrum across which the bearings have to work.

Iglidur plastic bearings

In view of these criteria, the suggestions made by Igus were the most convincing: all bearing points of the SolarOptimus are now equipped with Igus products. On the main axes of the frame systems, which are around 20m long, Iglidur plastic bearings ensure low-friction and maintenance-free operation. The integrated solid lubricant of the high-performance polymer also guarantees that no lubricants have to be added. This is a central precondition for the long service life of the bearing under the given conditions.

With iglidur G, Conergy is using the 'all-rounder' among the numerous Iglidur materials, which is suitable for pivoting and rotary movements at low to medium speed. The Iglidur G bearings can also operate in dirty, dusty conditions without any problem.

To reduce the strain on the drive systems, the Conergy development engineers have used linear bearings in the adjustment systems. Here, too, high-performance polymers from Igus are used: the DryLin linear plain bearings guarantee the exact linear motion of the axes. The DryLin W bearing slides on a hard anodised aluminium rail profile, with this combination giving low-friction running without stick/slip effects. Igus adapted the mounting plate for the moving components to the requirements of the Conergy developers. Sand and dust have no effect whatsoever on this linear bearing: any debris is simply pushed away by a 'snowplough' effect without affecting the gliding properties.

Conergy decided to use Igubal rod end bearings for the couplings linking the solar module carriers. These connecting parts absorb high forces, have very good damping properties and weigh five times less then conventional metallic bearings. Even if the environment is polluted by fine or coarse dust, the rod end bearings remain maintenance-free. There is no danger of seizing or blocking, and the integrated solid lubricants ensure low friction with maximum resistance to abrasion.

Loads and speeds

The drives of the module frames, which are responsible for the north-south alignment, apply a force of 6800N, the drive of the main frames for east-west tracking 10000 N. The speed is low at a maximum of 4mm/s and the drive is moved through a maximum of one full revolution per day. Nevertheless, high demands are made on wear resistance because the environmental conditions affect all components. This is why Igus carried out comprehensive series of tests for Conergy, and had extremely abrasive sand imported from southern Spain, where the first SolarOptimus systems have been installed in the meantime. The result was that even under conditions that are tougher than reality, the Igus bearings did not have to be replaced over the whole calculated service life of the SolarOptimus. This also applies to the UV resistance of the plastic as well as the wide temperature range and the humidity.

In the meantime, the first SolarOptimus systems have been installed for some months now in southern Spain - with all the evidence pointing to the calculated increased yield being achieved by the astronomically supported tracking. After completion, 800 movable systems will be producing eco-friendly solar energy at this location and feeding it into the power network. In addition, Conergy has already planned several other projects with larger quantities of tracking systems. Bernd Krabbe says: "We have already sold SolarOptimus systems with an overall capacity of 13MW."

Igus is now developing customised bearings, which will reduce production costs for larger quantities. And the dynamic development of Conergy makes it highly likely that larger quantities will be required.

igus (UK) Ltd

51A Caswell Road
Brackmills
Northampton
NN4 7PW
UNITED KINGDOM

+44 (0)1604 677240

sales@igus.co.uk

www.igus.co.uk

More applications
2 days ago
Contrinex celebrates its 50th anniversary
Fifty years ago this week, Contrinex was founded by Peter Heimlicher in Switzerland. What began as a one-man operation, is now a technology-leading, innovative global company, serving over 60 countries and employing more than 500 people worldwide, and is led by Peter’s daughter, CEO Annette Heimlicher.
2 days ago
A full programme to inspire, inform and entertain
Manufacturing and Engineering Week (Birmingham NEC, 8-9 June) will be a celebration of British engineering, a two-day festival of innovation that will showcase the very best that UK industry has to offer, while also providing knowledge, inspiration and a touch of entertainment.
2 days ago
Maxon’s Drive Technology Insight day is a great success
11th May 2022 saw Maxon’s first Drive Technology Insight day bring together the engineering community in the UK and Ireland.
3 days ago
Nord Drivesystems exhibits at ‘all about automation’ 2022
On 29 and 30 June 2022, Nord Drivesystems will present the DuoDrive geared motor, the energy-efficient IE5+ synchronous motor, the new decentralised NORDAC ON frequency inverter and the NORDAC PRO SK 500P control cabinet inverter, at ‘all about automation’.
3 days ago
TÜV Süd certifies Pilz product development as safe and secure
TÜV Süd has certified the development processes of Pilz in accordance with the international security standard IEC 62443-4-1. This addition to the existing functional safety management certification promises Pilz customers double security from now on.
3 days ago
Enclosures provide safety and ease of use for laser interlocks
Laser Support Services, which designs interlock systems, works with Spelsberg UK as its enclosure partner, based on the quality and flexibility of the housings.
4 days ago
Camozzi launches new UK short form catalogue
Camozzi Automation has launched its new UK short form catalogue, available both online and in hard copy format.
5 days ago
NSK roller guides increase uptime of blow moulding machines
A manufacturer of PET (polyethylene terephthalate) bottles frequently had to replace the linear guides on its blow moulding machines. However, after switching to NSK’s RA series roller guides, there have been no failures for over a year, producing annual cost savings in maintenance, spare parts and downtime of €60,000.
5 days ago
Design your future at Design Engineering Expo 2022
With innovation at its core, Design Engineering Expo 2022 is the perfect place for forward thinking design engineering professionals to gain insight into new technologies, learn how to improve efficiencies and gain inspiration for ideas they can implement into their workplace, to put them ahead of their competitors and form part of their future strategy.
5 days ago
Tray handling system gently handles medical-use glass cartridges
Gerresheimer Medical Systems Division produces over one billion high quality, medical grade, glass cartridges every year and central to its new post-production inspection and packaging system is the IEF Werner varioSTACK CF (Clean Factory) tray palletiser.

Login / Sign up