Tips for mitigating harmful harmonics

The rise of non-linear loads in industrial environments over the last two decades has resulted in the growing problem of harmonic currents and utility-level voltage distortion. Facing a lack of awareness, the industry has struggled to implement effective mitigation techniques. Here, global business development manager of CP Automation, John Mitchell, discusses offers useful tips for mitigating harmonics.

Voltage distortion caused by current harmonics can wreak havoc in a plant, its equipment and the mains power supply. Damage can be serious and varied with the most common symptoms including voltage notching, motor vibration, arcing on bearings, nuisance tripping, electromagnetic interference (EMI/RFI) and overheating.

The very first place to start is to ensure you comply with regulations. International harmonic control requirement, IEEE-519, limits "the maximum frequency voltage harmonic to 3 per cent of the fundamental and the voltage total harmonic distortion (THD) to 5 per cent for systems with a major parallel resonance at one of the injected frequencies." Some form of filtering is subsequently recommended.

We are lucky in the UK to have a stiff power grid, but this is not true everywhere. Developing countries often are not as lucky. Weak grids with an unreliable supply and inadequate infrastructure are common in other parts of the world. The power ratings on products are often based on calculations performed in ideal conditions. Buyers would be wise to note that these products may perform adversely in weak grids and may not perform to IEEE-519 standards in these conditions.

Remember to always stay on your toes. The last few decades have seen a rise in the use of non-linear loads such as transistor based variable speed drives (VSDs) and line-commutated DC drive systems. The processes of high-frequency switching and pulse width modulation (PWM), introduce unwanted multiples of the fundamental 50Hz frequency in the form of harmonics. Knowing what options are available to you can help the overall efficiency of the harmonic mitigation process.

Passive and active harmonic systems can be installed in both series and parallel (shunt) configurations within a system. Series solutions operate in line with the load, meaning that units must be sized for the full current load. Shunt units can be sized only for the harmonic disturbance. There is a clear decision to be made between series-passive, shunt-passive, series-active and shunt-active systems.

Series-passive

The most straight forward series-passive approach can be achieved using a line reactor. This is a low-cost way to reduce current harmonics, whilst adding a level of protection to the rectifier.

Shunt-passive

Shunt passive is power factor correction, often using fixed capacitor banks, tuned and detuned contactor based units, thyristor capacitor banks and fine tuned passive filters. These methods were principally developed to resolve reactive power and not specifically for harmonic mitigation. Today, I would hope no one is installing capacitor banks by themselves and, at the very least, using de-tuned ones - with an inductor for example.

Series-active

Series-active takes the form of an Active-Front-End (AFE) variable speed drive (VSD). It replaces the rectifier diodes in a regular VSD with an IGBT controlled rectifier to eliminate switching-based signal noise.

AFEs are great at significantly lowering THD and maintaining good power factor. However AFEs have some serious drawbacks. In order to maintain a small form factor, lower switching frequencies are used, which result in high switch ripples on the voltage waveform. This can cause other sensitive equipment like PLCs and telemetry and communications networks to nuisance trip and malfunction.

In addition, although this unit may at first seem to eliminate harmonics, it must be noted that with the AFE in addition to the VSD, there are now two drives in the circuit producing twice the heat. This means twice the heat and with a 200kW AFE it soon adds up. For the panel builder / system integrator, bigger cooling systems are needed to cope with the excessive heat.

Shunt-active

Active filters provide the most efficient harmonic compensation in a compact unit that has little loss, is insensitive to grid conditions, cannot be overloaded and is easy to retrofit. All of this comes at a slightly higher cost, which is offset by the better return on investment over the longer term.

Understanding the often subtle differences between various harmonic filtering technologies can yield better cost savings, reduce complexity and prolong equipment life. Understanding what options are available really is worth it in the long run.

For more information about mitigating harmonics please visit www.cpaltd.net.

CP Automation Ltd

Unit 8, Ashley Industrial Estate
Exmoor Avenue
Scunthorpe
DN15 8NJ
UNITED KINGDOM

+44 (0)1724 851515

enquiries@cpaltd.net

www.cpaltd.net

More technical articles
49 minutes ago
Last few places on Machinery Safety Course
Just a handful of places remain available on the last Pilz City & Guilds accredited Machinery Safety Course in 2020. Diary date is December 14th to 17th
4 hours ago
Camozzi Automation launches new quick exhaust safety valves
Designed to provide a plug and play solution for OEMs that need to be compliant with Machinery Directive 2006/42/EC, Camozzi Automation says that its new quick exhaust 2-way safety valve range also complies with ISO 13849-1 covering the safe design of control systems which perform safety functions
4 hours ago
SICK’s Open Service for IO-Link function blocks
A new open software service for control systems has been introduced by SICK
3 days ago
Automatic bearing lubrication brings ore inspiring results in mining
By installing automatic lubricators for bearings on its conveyor drive motors and belt pulleys, an opencast mine in Hungary has seen a range of benefits, including the prevention of unplanned downtime, longer bearing life and reduced repair work
3 days ago
Kinoulton company conveys COVID-combating masks
Here's a great example of the germ of an idea resulting in the combating of COVID
3 days ago
FLIR Systems announces four new Exx-Series handheld thermal imaging cameras
New E96, E86, E76 and E54 models feature enhanced thermal resolution and provide on-camera routing capability for more efficient inspections
4 days ago
New C-Mount lenses bring focus for machine and system builders
IDS now offers more than 20 new C-mount lenses with resolutions of 5, 8 and 10 MP as well as different focal lengths and optical classes
4 days ago
Backup DC motor for two rolling mill applications
Menzel Elektromotoren has built a replica of an old DC motor for a large German steel strip manufacturer
4 days ago
Distributed safety systems webinar 30th October 0930
In this webinar Pilz UK Product Manager David Collier will examine the state-of-the-art technology available to meet the demands of decentralisation
4 days ago
New narrow FeedThrough connectors save panel space
New from Cliff Electronics is the SLIMS FeedThrough Connector range, designed and manufactured in the UK